AQUALIS – CALEO MICROCONNECT N B Installation Fonctionnement Mise en service Maintenance Installation Operation Commissioning Maintenance. Aqualis Caleo. 60H. 60HT. 70HT. Heating capacity *. kW. Power input *. kW. COP. Refrigerant fluid RC – Load. CIA. T CALEO. 10 – NA E. Instruction manual . The TDC series AQUACIAT CALEO heat pumps meet the heating needs of 0 = Aqualis Caleo.
|Published (Last):||4 November 2012|
|PDF File Size:||2.12 Mb|
|ePub File Size:||13.45 Mb|
|Price:||Free* [*Free Regsitration Required]|
AQUALIS CALEO |
If you have a radiant floor heating system, only use pressurised neutral gas compressed air, nitrogen to blow out the water remaining in the water loops. If this is not the case, follow the procedure below: To do so, first insert the tabs Fig.
Stage-1 electric auxiliary unit operation Indicator 4: It is essential that they be fitted if the unit is installed on anti-vibration mounts. As the hot water. Check the glycol content if used. Do not throw it away. Always aqualiis with the appropriate bend radius. Mandatory annual checks Leaks on the refrigeration circuit.
With the unit running, check it thoroughly for any abnormal visual signs or noises. Walls can increase noise levels considerably and reflect noise in various directions. Always top up with the same type of mix initially used. D e u t s ch If you do not have a torque wrench, tighten them until they are snug then tighten a further quarter turn.
Cool ing [kw] Heating [kw] 1 1 General More information. This can be done by opening the manual bleed valve located cxleo the unit cover when turning the unit on or by installing a section of the water line and an automatic bleed valve over the unit.
Although it is rain resistant, it may be installed under a shelter with adequate ventilation on all four sides.
Power Type More information. Wireless room temperature controller with hour time switch and LCD. Fig 1 1 Remove the middle screw rear of unit 2 Detach both ends as shown in picture 3 Remove of the top by sliding it toward the rear – The characteristics of the mains supply must be identical to those on the data plate. Access aqialis level-2 installer settings For further information on reading and programming the terminal, refer calwo the manual provided with it.
Connect a contact to connector J2 terminals 3 and calwo on your unit s Microconnect board. Taking temperature readings is sufficient in most cases. The predominant problem with outdoor units is disturbance caused to the neighbourhood because of noise. Please read before installation More information. To keep your system running smoothly and, more specifically, if your Aqualis Caleo is installed at a high point, you must bleed the air contained inside it at the time of commissioning.
Air/water heat pump – AQUALIS R series – CIAT
If so, the terminal may be located anywhere without affecting control see paragraph under table on page The analysis will reveal whether the water is suitable for use with the various materials it will come into contact with and prevent the formation of electrolytic couples: However, special applications e.
It is not necessary to add glycol to your system if you are absolutely sure that there is no risk of freezing temperatures in your area. D e u t s ch – Open the valves on the water circuits and make sure water is flowing through the heat pump. Insulate the filter or install it indoors protect from freezing temperatures.
A few recommendations – Do not run the burner and the heat pump at the same time when the water temperature is below 40 C. Check your local electrical codes and regulations.
Description The Alpha Climatic energy. The control setpoint is displayed in all other cases. Aquails by dry contact J15 In hot water production mode heating, pool, frost protection or domestic hot water modes or when compressor turned off: The room temperature is managed by the Microconnect terminal.
Clean the drain pan.
When you purchase the Diana Instant Hot Water tank, contents include: Page 2 Compressor More information. Then attach the mounting plate to a wall using the screws and anchor bolts or a flush-mount box 60 mm centre distance using the holes Fig.
Access to level-1 customer settings Indicator 0: Setting P34 may be used to turn off the circulator. Power Type Battery power More information.